view release on metacpan or  search on metacpan

lib/AI/NeuralNet/Simple.pm  view on Meta::CPAN

available with three of the most common being the linear, sigmoid, and tahn
activation functions.  For technical reasons, the linear activation function
cannot be used with the type of network that C<AI::NeuralNet::Simple> employs.
This module uses the sigmoid activation function.  (More information about
these can be found by reading the information in the L<SEE ALSO> section or by
just searching with Google.)

Once the activation function is applied, the output is then sent through the
next synapse, where it will be multiplied by w4 and the process will continue.

=head2 C<AI::NeuralNet::Simple> architecture

The architecture used by this module has (at present) 3 fixed layers of
neurons: an input, hidden, and output layer.  In practice, a 3 layer network is
applicable to many problems for which a neural network is appropriate, but this
is not always the case.  In this module, we've settled on a fixed 3 layer
network for simplicity.

Here's how a three layer network might learn "logical or".  First, we need to
determine how many inputs and outputs we'll have.  The inputs are simple, we'll
choose two inputs as this is the minimum necessary to teach a network this
concept.  For the outputs, we'll also choose two neurons, with the neuron with
the highest output value being the "true" or "false" response that we are
looking for.  We'll only have one neuron for the hidden layer.  Thus, we get a
network that resembles the following:

           Input   Hidden   Output

 input1  ----> n1 -+    +----> n4 --->  output1
                    \  /
                     n3
                    /  \
 input2  ----> n2 -+    +----> n5 --->  output2

Let's say that output 1 will correspond to "false" and output 2 will correspond
to true.  If we feed 1 (or true) or both input 1 and input 2, we hope that output
2 will be true and output 1 will be false.  The following table should illustrate
the expected results:

 input   output
 1   2   1    2
 -----   ------
 1   1   0    1
 1   0   0    1
 0   1   0    1
 0   0   1    0

The type of network we use is a forward-feed back error propagation network,
referred to as a back-propagation network, for short.  The way it works is
simple.  When we feed in our input, it travels from the input to hidden layers
and then to the output layers.  This is the "feed forward" part.  We then
compare the output to the expected results and measure how far off we are.  We
then adjust the weights on the "output to hidden" synapses, measure the error
on the hidden nodes and then adjust the weights on the "hidden to input"
synapses.  This is what is referred to as "back error propagation".

We continue this process until the amount of error is small enough that we are
satisfied.  In reality, we will rarely if ever get precise results from the
network, but we learn various strategies to interpret the results.  In the
example above, we use a "winner takes all" strategy.  Which ever of the output
nodes has the greatest value will be the "winner", and thus the answer.

In the examples directory, you will find a program named "logical_or.pl" which
demonstrates the above process.

=head2 Building a network

In creating a new neural network, there are three basic steps:

=over 4

=item 1 Designing

This is choosing the number of layers and the number of neurons per layer.  In
C<AI::NeuralNet::Simple>, the number of layers is fixed.

With more complete neural net packages, you can also pick which activation
functions you wish to use and the "learn rate" of the neurons.

=item 2 Training

This involves feeding the neural network enough data until the error rate is
low enough to be acceptable.  Often we have a large data set and merely keep
iterating until the desired error rate is achieved.

=item 3 Measuring results

One frequent mistake made with neural networks is failing to test the network
with different data from the training data.  It's quite possible for a
backpropagation network to hit what is known as a "local minimum" which is not
truly where it should be.  This will cause false results.  To check for this,
after training we often feed in other known good data for verification.  If the
results are not satisfactory, perhaps a different number of neurons per layer
should be tried or a different set of training data should be supplied.

=back

=head1 Programming C<AI::NeuralNet::Simple>

=head2 C<new($input, $hidden, $output)>

C<new()> accepts three integers.  These number represent the number of nodes in
the input, hidden, and output layers, respectively.  To create the "logical or"
network described earlier:

  my $net = AI::NeuralNet::Simple->new(2,1,2);

By default, the activation function for the neurons is the sigmoid function
S() with delta = 1:

	S(x) = 1 / (1 + exp(-delta * x))

but you can change the delta after creation.  You can also use a bipolar
activation function T(), using the hyperbolic tangent:

	T(x) = tanh(delta * x)
	tanh(x) = (exp(x) - exp(-x)) / (exp(x) + exp(-x))

which allows the network to have neurons negatively impacting the weight,
since T() is a signed function between (-1,+1) whereas S() only falls
within (0,1).

=head2 C<delta($delta)>

Fetches the current I<delta> used in activation functions to scale the
signal, or sets the new I<delta>. The higher the delta, the steeper the
activation function will be.  The argument must be strictly positive.

You should not change I<delta> during the traning.

=head2 C<use_bipolar($boolean)>

Returns whether the network currently uses a bipolar activation function.
If an argument is supplied, instruct the network to use a bipolar activation
function or not.

You should not change the activation function during the traning.

=head2 C<train(\@input, \@output)>

This method trains the network to associate the input data set with the output
data set.  Representing the "logical or" is as follows:

  $net->train([1,1] => [0,1]);
  $net->train([1,0] => [0,1]);
  $net->train([0,1] => [0,1]);
  $net->train([0,0] => [1,0]);